InFocus Home Theater System QR80421 User Manual

5100  
Regulatory models: W59  
 
QR80421  
WARNING: Do not look into laser beam emitted from the front of the  
remote control.  
CAUTION: Use of controls or adjustments or performance of procedures  
other than those specified herein may result in hazardous radiation  
exposure. Class 2 Laser product; maximum output 1mW; wavelength  
650nm.  
[Class 2 Laser Product] Wavelength 650nm; Maximum output 1mW; No  
beam divergence.  
IEC60825-1:2007 EN60825-1:2007  
[Laser Diode] Wave length 650nm; Maximum power 7mW; Beam diver-  
gence 33deg (perpendicular)/8deg (parallel).  
OR  
IEC60825-1:1993 +A1:1997 +A2:2001  
Location of laser beam warning labels on remote  
 
2
Table of Contents  
For complete details on connecting and operating the projector, refer to this  
User’s Guide.  
Connecting a computer  
8
The website also has technical specifications (an interactive image size cal-  
culator, laptop activation commands, connector pin outs, a glossary, the  
product data sheet), a web store to buy accessories, and a page for online  
registration.  
33  
Settings menu  
42  
Command Control  
 
3
Important Operating Considerations for Safety  
Place the projector in a horizontal position no greater than 8 degrees off  
axis.  
Locate the projector in a well-ventilated area without any obstructions  
to intake or exhaust vents. Do not place the projector on a tablecloth or  
other soft covering that may block the vents.  
/ 1 m  
2’  
3’  
/ 0.6 m  
Locate the projector at least 4' (1.2 m) away from any heating or cooling  
vents.  
m
5
.
8
/ 2  
.
4
/ 1  
m
5
Use only approved ceiling mounts.  
Warning: To prevent eye injury if the projector is ceiling mounted,  
wear protective eyewear before opening lamp door. A warning sticker  
is included with the user documentation. Place this sticker on the lamp  
door if the projector is mounted on the ceiling.  
Follow these instructions to help ensure image quality and lamp life over  
the life of the projector. Failure to follow these instructions may affect the  
warranty. For complete details of the warranty, see the Warranty booklet.  
Only genuine InFocus lamps are tested for use in this projector. InFo-  
cus is not liable for the performance, safety or certification of any other  
lamps. The use of other lamps violates the projector warranty and  
voids all certification marks on this projector.  
Use only the power cord provided. A surge-protected power strip is  
recommended.  
Refer to this manual for proper startup and shutdown procedures.  
Hg – Lamp contains mercury. Manage in accordance with local  
disposal laws. See www.lamprecycle.org.  
In the unlikely event of a lamp rupture, particles may exit through the  
projector vents. When the projector is turned on, keep people, food,  
and drinks out of the "keep out" area under and around the projector,  
as indicated by the "X" areas.  
 
4
Projector components and features: front  
Introduction  
Your new multimedia projector provides three computer, three video, and  
four audio inputs, one audio output, and RS-232 and Network control. It  
has WUXGA 1920 x 1200 resolution. The projector is easy to connect, easy to  
use, and easy to maintain.  
zoom/offset door  
remote  
control  
receiver  
Product specifications  
To read the latest specifications on your multimedia projector, be sure to  
visit our website. Web address information is located on the back inside  
cover of this User’s Guide.  
air intake  
vent  
heat vent  
Online Registration  
Register your projector on our website to receive product updates,  
announcements, and registration incentives. See the inside back cover for  
the web address.  
elevator foot release  
leveling foot  
focus  
Included Items  
Projector components and features: back  
lamp door  
projector  
remote  
lens cap*  
power cable  
VGA computer cable  
A/V cable  
documentation  
*The lens cap is tethered to the projector.  
power switch  
power plug  
connectors  
 
5
       
Connector Panel  
component video  
remote  
The projector provides three computer and three video connection options:  
audio in 1,2  
VGA computer  
monitor  
BNC  
RJ-45  
HDMI  
USB  
control  
receiver  
(IR)  
one VGA computer  
RS232  
lock  
serial control  
one HDMI™ (High Definition Multimedia Interface)*  
one component BNC (G/Y, B/C /P , R/C /P , H, V)  
B
B
R
R
one component RCA video (Pr, Pb, Y)  
one S-video  
one composite RCA video  
The projector provides computer and video connectors for audio support:  
two composite RCA stereo audio (L, R)  
one audio out  
composite  
audio in 3,4  
power connector and switch  
wired remote  
s-video  
video  
external  
speakers  
(audio out)  
two audio ins  
speaker  
The projector also provides the following connectors:  
one wired remote  
one monitor out  
RS-232 serial connector (for serial control)  
RJ-45 connector (for networked control)  
The RS-232 Command Line Interface (CLI) specifications and commands  
port.  
* HDMI is an industry standard, uncompressed, all-digital audio/video  
interface that connects between sources, such as set-top boxes, DVD play-  
ers, and receivers and your projector. To take advantage of HDMI 1.3 you  
must have a 1.3-compatible source. The HDMI, because it is a digital signal,  
yields the highest quality image. It is common for these signals to be  
encrypted with HDCP (high-bandwidth digital-content protection). Your  
new projector ships standard with decryption codes so you can enjoy these  
high quality, all digital images.  
 
6
     
Positioning the projector  
To determine where to position the projector, consider the size and shape of  
your screen, the location of your power outlets, and the distance between  
the projector and the rest of your equipment. Here are some general guide-  
lines:  
Projection angle in 16:10 mode (default)  
10’ high image  
10:0  
1:1  
Position the projector on a flat surface at a right angle to the screen. The  
projector must be at least 3 feet (0.9m) from the projection screen.  
lens center  
Position the projector within 10 feet (3m) of your power source and  
within 6 feet (1.8m) of your video device (unless you purchase exten-  
sion cables). To ensure adequate cable access, do not place the projector  
within 6 inches (.15m) of a wall or other object.  
10:0  
bottom of image  
at lens center  
If you are installing the projector on the ceiling, refer to the installation  
guide that comes with the Ceiling Mount Kit for more information. To  
turn the image upside down, see “Ceiling” on page 33. We recommend  
using an authorized ceiling mount. The Ceiling Mount Kit is sold sepa-  
rately; visit our website for more information.  
1:1  
bottom of image  
50% below  
lens center  
Position the projector the desired distance from the screen. The dis-  
tance from the lens of the projector to the screen, the zoom setting, and  
the video format determine the size of the projected image. For infor-  
mation about image sizes at different distances, see “Projected image  
For the standard lens that comes with the projector, the image exits at a  
given angle. However, the lens shift feature makes the image offset  
variable. The image offset is 100% at a 10:1 ratio when the projector is in  
16:10 mode (default mode). This means that if you have an image 10’  
high, the bottom of the image will be at the center of the lens.  
The image offset is 50% when the lens shift is at a 1:1 ratio. This means  
that if you have an image 10’ high, the bottom of the image will be 5’  
below the center of the lens.  
 
7
       
Connecting a computer  
connect computer cable  
Required computer connections  
Connect one end of the VGA computer cable to the Computer 2 connector  
on the projector. Connect the other end to the video port on your computer.  
If you are using a desktop computer, you first need to disconnect the moni-  
tor cable from the computer’s video port.  
Connect the black power cable to the connector on the back of the projector  
and to your electrical outlet.  
connect power cable  
NOTE: Always use the power cable that shipped with the projector.  
Optional computer connections  
You can also connect to your computer using optional BNC or HDMI  
cables. Connect the BNC connectors on the BNC cable to the appropriate  
Computer 3 connectors on the projector. Connect the other end to the video  
port on your computer. If you are using a desktop computer, you first need  
to disconnect the monitor cable from the computer’s video port.  
Or, connect the HDMI cable to the Computer 1 connector.  
connect BNC cable  
connect HDMI cable  
To have sound with your presentation, connect the audio cable to your  
computer and to the corresponding computer Audio In connector on the pro-  
jector. You can assign a particular source to a particular audio in connector,  
see page 33.  
connect audio cable  
 
8
             
If you are using a desktop computer and want to see the image on your  
computer screen as well as on the projection screen, plug the monitor cable  
to the Monitor out connector on the projector.  
connect monitor cable  
connect RS-232 cable  
You can control the projector from an LCD control panel, touch screen, or  
other control device or computer by connecting an RS-232 cable to the pro-  
jector’s Serial Control connector. Specific RS-232 commands can be found in  
the Service and Support section of our website and in the Appendix.  
The projector can be managed by networking software through its Network  
(RJ-45) connector. Detailed instructions on this feature can be found on our  
website.  
connect CAT-5 cable  
Network  
 
9
         
Displaying a computer image  
Remove the lens cap.  
remove lens cap  
Press the power switch on the back of the projector to the on (I) position.  
The Power light on the Status Indicator Panel (page 15) lights green.  
press Power switch press Power button  
2
Press the Power button on the top of the projector or the remote.  
The Power light blinks green and the fans start to run. When the lamp  
comes on, the startup screen is displayed and the light is steady green. It can  
take a minute for the image to achieve full brightness.  
1
? No startup screen? Get help on page 16.  
turn on computer  
Turn on your computer.  
The computer’s image should appear on the projection screen. If it doesn’t,  
press the Source button on the keypad or remote.  
activate laptop’s external port  
Make sure your laptop’s external video port is active.  
Many laptops do not automatically turn on their external video port when a  
projector is connected. Usually a key combination like FN + F5 is used to  
turn the external display on and off. Refer to your computer’s documenta-  
tion to learn your computer’s key combination.  
? No computer image? Get help on page 16.  
Download from Www.Somanuals.co1m0. All Manuals Search And Download.  
     
Adjusting the image  
release  
button  
adjust height  
release  
button  
Adjust the height of the projector, if necessary, by pressing the release but-  
tons on each side of the projector’s front to extend the elevator feet.  
elevator  
foot  
elevator  
foot  
Position the projector the desired distance from the screen at a 90 degree  
angle (perpendicular) to the screen.  
adjust distance  
See page 41 for a table listing screen sizes and distances.  
Adjust the zoom by rotating the Zoom ring inside the lens door until the  
desired image size is produced.  
adjust zoom and focus  
Adjust the focus by rotating the Focus ring on the lens until the desired  
focus is produced.  
adjust lens shift  
If the image is not on the screen or viewing area, adjust it by using the lens  
shift dials inside the lens door.  
Use the right dial to shift the lens left or right. Use the left dial to shift the  
lens up or down.  
contrast  
brightness  
adjust Contrast or Brightness  
Adjust the Contrast or Brightness in the Picture menu.  
See page 27 for help with the menus.  
Download from Www.Somanuals.co1m1. All Manuals Search And Download.  
             
Connecting a video device  
Standard video connections  
connect A/V cable  
Plug the audio/video (A/V) cable’s yellow connector into the video-out  
connector on the video device. Plug the other yellow connector into the yel-  
low Video 3 connector on the projector. Plug a white connector into the left  
audio out connector on the video device and plug a red connector into the  
right audio out connector on the video device. Plug the remaining white  
connector into a left audio in connector on the projector, and plug the red  
connector into a right audio in connector on the projector. You can assign a  
particular source to a particular audio in connector, see page 33.  
connect power cable  
Connect the black power cable to the connector on the back of the projector  
and to your electrical outlet.  
NOTE: Always use the power cable that shipped with the projector.  
Optional video connections  
If the video device uses a round, four-prong S-video connector, plug an  
S-video cable (sold separately) into the S-video connector on the video  
device and into the Video 2 connector on the projector. Use the A/V cable’s  
audio connectors as described directly above (the yellow connectors on the  
A/V cable are not used).  
connect S-video and video cables  
If the video device uses component cable connectors (sold separately), plug  
the cable’s green connectors into the green component-out connector on the  
video device and into the Video 1 green component connector (labeled “Y”)  
on the projector. Plug the component cable’s blue connectors into the blue  
component-out connector on the video device and into the blue component  
connector (labeled “Cb/Pb”) on the projector. Plug the component cable’s  
red connectors into the red component-out connector on the video device  
and into the red component connector (labeled “Cr/Pr”) on the projector.  
Use the A/V cable’s audio connectors as described above (the yellow con-  
nectors on the A/V cable are not used). NOTE: The component connectors  
can be used for HDTV sources (480i, 480p, 720p, 576i and 1080i formats).  
connect component cables  
and video cables  
Download from Www.Somanuals.co1m2. All Manuals Search And Download.  
                 
Displaying a video image  
Remove the lens cap.  
remove lens cap  
Press the power switch on the back of the projector to the on (I) position.  
The Power light on the Status Indicator Panel (page 15) lights green.  
press Power switch  
press Power button  
Press the Power button on the top of the projector or the remote.  
2
The Power light blinks green and the fans start to run. When the lamp  
comes on, the startup screen is displayed and the light is steady green. It can  
take a minute for the image to achieve full brightness.  
1
? No startup screen? Get help on page 16.  
Plug in and turn on the video device.  
turn on video device  
The video device’s image should appear on the projection screen. If it  
doesn’t, press the Source button on the keypad or remote.  
adjust height  
release  
button  
release  
button  
Adjust the height of the projector, if necessary, by pressing the release but-  
tons on each side of the projector’s front to extend the elevator feet. Rotate  
the feet, if necessary, to level the projector.  
elevator  
foot  
elevator  
foot  
adjust distance  
Position the projector the desired distance from the screen at a 90 degree  
angle to the screen. See page 41 for a table listing screen sizes and distances  
to the screen.  
Download from Www.Somanuals.co1m3. All Manuals Search And Download.  
         
Adjust the zoom by rotating the Zoom ring, located inside the lens door,  
until the desired image size is produced.  
adjust Zoom and Focus  
Adjust the focus by rotating the Focus ring on the lens until the desired  
focus is produced.  
adjust Lens Shift  
If the image is not on the screen or viewing area, adjust it by using the lens  
shift dials inside the lens door.  
Use the right dial to shift the lens left or right. Use the left dial to shift the  
lens up or down.  
adjust volume  
Adjust the volume in the Audio menu.  
adjust Picture menu  
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.  
See page 27 for help with the menus.  
Download from Www.Somanuals.co1m4. All Manuals Search And Download.  
       
The Status Indicator Panel on top of the projector indicates the state of the  
projector and can help you troubleshoot.  
Shutting down the projector  
The projector automatically blanks the screen after no active source is  
detected for 5 minutes. This blank screen helps preserve the life of the pro-  
jector. The image returns when an active source is detected or a remote or  
keypad button is pressed.  
Screen Save  
Table 1: Status indicator light behavior and meaning  
You can make the blank screen appear after five minutes by turning on  
Screen Save in the Settings>System menu. See page 34.  
Status Indicator Panel icons  
Power, solid green  
Meaning  
Power Save  
The power button has been pressed and  
the software has initialized or the projec-  
tor has been powered off.  
The projector also has a Power Save feature that automatically turns the  
lamp off after no signals are detected for 20 minutes. After 10 additional  
minutes with no signal, the projector powers down. If an active signal is  
received before the projector powers down, the image is displayed. You  
must press the Power button to display an image after 30 minutes have  
passed. When Power Save is enabled, Screen Save is disabled. See page 34.  
Power, blinking green  
Thermometer  
The power button has been pressed and  
the software is initializing, or the projec-  
tor is powering down and the fans are  
running to cool the lamp.  
Turning off the projector  
To turn off the projector, press the power button and verify that you want to  
turn the projector off by pressing the power button again within 3 seconds.  
You can cancel the shutdown by not pressing the power button a second  
time. The lamp turns off and the Power light blinks green for over 1 minute  
while the fans continue to run to cool the lamp. When the lamp has cooled,  
the Power light is solid green and the fans stop. Press the power switch on  
the back of the projector and unplug the power cable to completely power  
off the projector.  
The projector is too hot. Make sure the  
vents aren’t blocked (see page 20). Turn  
off the projector and wait one minute,  
then turn the projector on again. Contact  
Technical Support if the problem persists.  
Lamp  
Turn off the projector and wait one min-  
ute, then turn the projector on again. If  
the lamp light turns on again, replace the  
lamp and reset the lamp timer.  
Troubleshooting your setup  
If your image appears correctly on the screen, skip to the next section. If it  
does not, troubleshoot the setup.  
Wrench/Service  
Turn off the projector and wait one min-  
ute, then turn the projector on again. If  
the service lamp turns on again, service is  
required. Visit our website to contact Ser-  
vice.  
Download from Www.Somanuals.co1m5. All Manuals Search And Download.  
           
Problem  
Solution  
Result  
Plug power cable in, press power switch and  
power button. Remove lens cap.  
No startup screen  
Correct image  
3
startu  
screen  
p
2
1
Computer image projected  
Only startup screen appears/no computer image  
Press the Source button  
Activate laptop’s external port  
startu  
screen  
p
A
A
A
or restart  
laptop  
Download from Www.Somanuals.co1m6. All Manuals Search And Download.  
           
Computer image projected  
Adjust computer refresh rate in Control  
Panel>Display>Settings>Advanced>  
No computer image, just the words “Signal out of range”  
Adapter (location varies by operating system)  
Signal  
range  
out  
of  
A
A
A
You may also need to set a different  
resolution on your computer, as shown  
in the following problem, “Image fuzzy  
or cropped”  
Image clear and not cropped  
Image fuzzy or cropped  
Set your computer’s display resolution to the  
native resolution of the projector  
A
(Start>Settings>Control Panel>Display>Settings  
tab, select1920x1200)  
A
A
For a laptop,  
disable laptop  
monitor  
or turn-on dual-  
display mode  
Download from Www.Somanuals.co1m7. All Manuals Search And Download.  
   
Projector troubleshooting  
Problem  
Solution  
Result  
Square image  
Image not square  
Adjust keystone in the Picture menu  
Correct image  
Adjust the focus ring or Sharpness in the  
Picture>Advanced menu  
Image not sharp  
A B  
A B  
Change aspect ratio to 16:9 in Picture>Aspect  
ratio menu  
Correct image  
Image does not fit 16:9 screen  
Download from Www.Somanuals.co1m8. All Manuals Search And Download.  
     
Correct image  
Turn on/off Ceiling in Settings>System menu  
Image upside down  
A
A B  
A B  
Image reversed left to right  
Turn on/off Rear in Settings>System menu  
Correct image  
A
Correct image  
Projected colors don’t match source  
Adjust color, tint, color temperature, brightness,  
contrast in the menus  
COLOR  
COLOR  
Download from Www.Somanuals.co1m9. All Manuals Search And Download.  
     
Make sure vents aren’t blocked; allow projector  
to cool for one minute  
Unplug projector; wait 20 minutes; plug in  
projector and turn it on: lamp lights  
Lamp won’t turn on, Temp light is lit (page 15)  
Temperature light  
startu  
p
screen  
Lamp may need to be replaced (page 38)  
Lamp won’t turn on, Lamp light is lit (page 15)  
Lamp light  
Lamp turns on  
startu  
p
screen  
Download from Www.Somanuals.co2m0. All Manuals Search And Download.  
   
Correct image  
Move projector, adjust zoom or lens shift, adjust  
height  
Image not centered on screen  
Adjust horizontal or vertical position in  
Picture>Advanced menu  
Still having problems?  
This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we  
recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its  
full value.  
Download from Www.Somanuals.co2m1. All Manuals Search And Download.  
     
Using the keypad buttons  
power–turns the projector on (page 10) and off (page 15).  
menu–opens the on-screen menus (page 27).  
up/down arrows–navigates to and adjusts settings in the menus (page 27).  
select–confirms choices made in the menus (page 27).  
source–switches among active sources  
Download from Www.Somanuals.co2m2. All Manuals Search And Download.  
 
LED  
navigation buttons  
Using the remote control  
The remote uses two (2) AAA batteries (not included). They are easily  
installed by sliding the cover off the remote's back, aligning the + and - ends  
of the batteries, sliding them into place, and then replacing the cover.  
laser  
button  
To operate, point the remote at the projection screen or at the projector (not  
at the computer). The range of optimum operation is about 16 feet (5m). For  
best results, aim the remote directly at the projector.  
backlight button  
source buttons  
To use the laser pointer, press and hold the Laser button. The laser turns off  
when the button is released, or times out after two (2) minutes of continu-  
ous operation.  
WARNING: Do not look into the laser beam emitted from the top of the  
remote control.  
The remote contains four Source buttons that allow you to assign a particu-  
lar input to a specific source. Simply press the numbered Source buttons to  
travel to whatever four sources you wish to have available.  
Troubleshooting the remote  
Press the remote's Menu button to open the projector's menu system. Use the  
arrow buttons to navigate, and the Select button to select features and adjust  
values in the menus.  
Make sure the batteries are installed in the proper orientation and are  
not dead. The LED at the top of the remote lights when any button is  
pressed when the battery power is adequate.  
Make sure you’re pointing the remote at the projector, not the com-  
puter, and are within the remote range of 16 feet (5m).  
The remote also has a power button to turn the projector on and off, volume  
buttons and a mute button to control the sound, a backlight button to light  
the remote's buttons in the dark, and a video and computer button to switch  
between those two sources.  
Two presentation-specific features are also provided. Use the blank button  
to display a blank screen instead of the current slide; use the effect button to  
invoke a user-definable action, such as freeze, or magnify.  
The Auto Image button reacquires the computer image and the Presets but-  
ton lets you customize the settings for each source. Up to three Preset set-  
tings can be customized and saved.  
Download from Www.Somanuals.co2m3. All Manuals Search And Download.  
   
Using the audio  
connect audio cable  
To play sound from the projector, connect your source to an Audio In con-  
nector on the projector.  
To adjust the volume, mute, or loudness, use the Audio menu (see page 33).  
Troubleshooting audio  
If there is no sound, check the following:  
Make sure the audio cable is connected.  
Make sure mute isn’t active.  
adjust volume  
Make sure the volume is turned up enough.  
Make sure you are connected to the corresponding audio in for your  
source. By default, Audio 1 corresponds to Computer 2, Audio 2 corre-  
sponds to Computer 3, Audio 3 corresponds to Video 2 and 3, and Audio  
4 corresponds to Video 1. You can change these assignments, see  
Adjust the audio source.  
If playing a video, make sure the playback has not been paused.  
external speakers  
Connecting external speakers  
The projector can be attached to external speakers that have their own  
power source by plugging a speaker cable into the projector’s Audio Out  
connector.  
speaker  
cable  
Download from Www.Somanuals.co2m4. All Manuals Search And Download.  
   
Optimizing computer images  
Presentation features  
After your computer is connected properly and the computer’s image is on  
the screen, you can optimize the image using the onscreen menus. For gen-  
eral information on using the menus, see page 27.  
Several features are provided to make giving presentation easier. The fol-  
lowing is an overview, details are found in the menu section on page 27.  
The Custom key, available on several optional remotes only, allows you  
to assign various features to the key. The default effect is Source Info.  
See page 35 for details.  
Adjust the Keystone, Contrast, or Brightness in the Picture menu.  
Change the Aspect Ratio. Aspect Ratio is the ratio of the image width to  
image height. Standard TV screens and older laptops are 4:3; HDTV  
and most DVDs are 16:9; and widescreen computers are 16:10. Choose  
the option that best fits your input source. See page 28 for details.  
The Freeze effect allows you to freeze the displayed image. This is use-  
ful if you want to make changes on your computer without your audi-  
ence seeing them.  
Adjust the Color Temperature in the Advanced menu.  
The Startup Logo menu option lets you change the default startup  
screen to a black, white, blue, or a custom logo screen via Capture New.  
See page 34.  
Adjust the Phase, Tracking, or Horizontal or Vertical position in the  
Advanced menu.  
Two menu options, Power Save and Screen Save, are provided to auto-  
matically shut down the projector after several minutes of inactivity or  
display a blank screen. This helps preserve lamp life. See page 34.  
Once you have optimized the image for a particular source, you can  
save the settings using Presets. This allows you to quickly recall these  
settings later. See page 29.  
A Low Power menu option is also available to help lower the projec-  
tor’s fan sound volume. See page 34.  
Download from Www.Somanuals.co2m5. All Manuals Search And Download.  
       
Optimizing video images  
Customizing the projector  
After the video device is connected properly and the image is on the screen,  
you can optimize the image using the onscreen menus. For general informa-  
tion on using the menus, see page 27.  
You can customize the projector for your specific setup and needs. See  
page 33 to page 36 for details on these features.  
For rear projection, turn Rear mode on in the Settings>System menu.  
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture  
menu. See page 28.  
For ceiling mounted projection, turn Ceiling mode on in the Set-  
tings>System menu.  
Change the Aspect ratio. Aspect ratio is the ratio of the image width to  
image height. Standard TV screens and older laptops are 4:3; HDTV  
and most DVDs are 16:9; and widescreen computers are 16:10. Choose  
the option that best fits your input source. See page 28.  
Specify which source the projector checks first for an active signal dur-  
ing power-up.  
Turn the projector’s on-screen display messages on and off.  
Turn on power saving features.  
Select a Sharpness setting. See page 29.  
Specify blank screen colors and startup logos.  
Specify the menu language.  
Adjust the Color Temperature. Select a listed value, or select User and  
individually adjust the intensity of the red, green, and blue color. See  
Control your projector using RS232 commands. See page 9 and  
Download from Www.Somanuals.co2m6. All Manuals Search And Download.  
       
Using the menus  
To open the menus, press the menu button on the keypad or remote. (The  
menus automatically close after 60 seconds if no buttons are pressed.) The  
Main menu appears. Use the arrow buttons to move up and down to high-  
light the desired submenu, then press the Select button.  
Menu  
button  
To change a menu setting, highlight it, press Select, then use the up and  
down arrow buttons to adjust the value, select an option using radio but-  
tons, or turn the feature on or off using check boxes. Press Select to confirm  
your changes. Use the arrows to navigate to another setting. When your  
adjustments are complete, navigate to Previous, then press Select to go to  
the previous menu; press the Menu button at any time to close the menus.  
Keypad navigation  
buttons  
Main menu  
Dots appear before the menu name. The number of dots indicate the menu’s  
level, ranging from one (the Main menu) to five (the most nested menus).  
Dots  
The menus are grouped by usage:  
The Picture menu provides image adjustments.  
The Settings menu provides set-up type adjustments that are not  
changed often.  
The Source Info menu provides a read-only display of information  
about the projector and source.  
Settings  
menu  
Picture  
menu  
Certain menu items may be grayed out until a particular source is con-  
nected. For example, Tint is only available for video sources and will be hid-  
den when a computer source is active. Other menu items may be grayed out  
when they are not available. For example, Brightness is grayed out until an  
image is active.  
Source Info menu  
Download from Www.Somanuals.co2m7. All Manuals Search And Download.  
     
Picture menu  
To adjust the following six settings, highlight the setting, press Select, use  
the up and down arrows to adjust the values, then press select to confirm  
the changes.  
Keystone Vertical  
increasing keystone  
decreasing keystone  
Keystone Vertical: adjusts the image vertically and makes a squarer image by  
using an adjustable scale band.  
Keystone Horizontal: adjusts the image horizontally and makes a squarer  
image by using an adjustable scale band.  
Corner Correction: allows you to adjust the corners of the projected image.  
This is particularly helpful when stacking projectors. Select the corner you  
would like to adjust within the Corner Correction submenu and follow the  
instructions on the screen to make desired adjustments.  
Keystone Horizontal  
Contrast: controls the degree of difference between the lightest and darkest  
parts of the picture and changes the amount of black and white in the  
image.  
Brightness: changes the intensity of the image.  
Color: (Computer 1 and video sources only) adjusts a video image from  
black and white to fully saturated color.  
Tint: (Computer 1 and NTSC video sources only) adjusts the red-green color  
balance in the image.  
Auto Image: resynchs the projector to the source.  
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.  
Standard TV screens and older laptops are 4:3; HDTV and most DVDs are  
16:9; and widescreen computers are 16:10. The default is 16:10, which dis-  
plays the input resized up or down to fill the display area.  
Corner Correction  
Aspect Ratio  
Download from Www.Somanuals.co2m8. All Manuals Search And Download.  
       
Presets: Presets are provided that optimize the projector for displaying com-  
puter presentations and video images in different lighting conditions and  
on different backgrounds.  
There are also user-definable presets. To set a preset for the current source,  
adjust the image, select Save Settings in the Presets menu, then select Save  
User Presets 1 (or 2 or 3). You can recall these settings in the future by select-  
ing the User 1 preset. If you select User Presets then further adjust the  
image, Presets Off will automatically be selected in the Preset menu to indi-  
cate changes have been made.  
Save Settings  
To restore the factory default settings, choose Factory Reset in the Set-  
tings>Service menu.  
Presets  
Advanced settings  
Sharpness: changes the clarity of the edges of a video image. Select a sharp-  
ness setting.  
Color Space: This option applies to computer and component video sources  
(except 480i/576i). It allows you to select a color space that has been specifi-  
cally tuned for the input signal. When Auto is selected, the projector auto-  
matically determines the standard. To choose a different setting, turn off  
Auto, then choose RGB for computer sources, RGB Video for HDMI com-  
puter sources, and either REC709 or REC601 for component video sources.  
Sharpness  
Advanced  
Color Temperature: changes the intensity of the colors. Select a listed value,  
or select User and individually adjust the intensity of the red, green, and  
blue colors.  
Color Space  
Color Temperature  
Download from Www.Somanuals.co2m9. All Manuals Search And Download.  
     
Video Standard: when set to Auto, the projector attempts to automatically  
pick the video standard based on the input signal it receives. (The video  
standard options may vary depending on your region of the world.) If the  
projector is unable to detect the correct standard, the colors may not look  
right or the image may appear “torn.” If this happens, manually select a  
video standard by selecting NTSC, PAL, or SECAM from the Video Stan-  
dard menu.  
On: Always display captions. Off: Never display captions. Channel: Selects  
which captions to display.  
.
Video Standard  
Active Iris: when on, the projector monitors the image brightness and modi-  
fies the light output if the image is dark, which improves black levels. In  
Presentation mode, it looks at peak brightness, in Theater mode it looks at  
average brightness.  
Active Iris  
Overscan: (Computer 1 and video sources only) removes noise around the  
video image.  
The following 4 options are for computer sources only:  
Phase: adjusts the horizontal phase of computer 2, 3 and component (except  
480i and 576i) sources.  
Tracking: adjusts the horizontal scan of a computer source (except Computer  
1).  
Horizontal / Vertical Position: adjusts the position of a computer source  
(except Computer 1) and Video 1 source (except 480i and 576i).  
Resolution: When this feature is set to Auto, the projector attempts to pick  
the resolution standard based on the input signal it receives. If the projector  
is unable to detect the correct standard, the resolution may look odd. If this  
happens, manually select the resolution from the menu which matches your  
source signal.  
Computer 2  
Computer 3  
Computer 2: allows you to turn Sync on Green on for this source.  
Computer 3: allows you to turn Sync on Green on for this source.  
Closed Captions: can be shown when the source is analog - component (480i  
only), or S-video or composite (NTSC only). The video signal must also  
include caption information. Auto: Display captions when sound is muted.  
Download from Www.Somanuals.co3m0. All Manuals Search And Download.  
   
Split Screen  
Split Screen lets you show two different sources at the same time, one on the left half of the screen and the other on the right. The following source combina-  
tions are supported:  
Table 2: Split Screen Matrix  
Computer 1  
Computer 2  
X
Computer 3  
Video 1  
Video 2  
Video 3  
Computer 1  
Computer 2  
Computer 3  
Video 1  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Video 2  
X
X
Video 3  
Download from Www.Somanuals.co3m1. All Manuals Search And Download.  
Exit or Previous: Removes the Split Screen Menu (if Split Screen is on) or goes  
to the Picture menu (if Split Screen is off).  
Most picture settings can’t be adjusted (e.g. Brightness, Contrast, Keystone,  
Overscan, Presets, etc.).  
Split Screen: Check the box to turn on Split Screen, or un-check it to turn off  
To change these settings:  
Split Screen.  
Make sure the source you want to adjust is the main source (See above for a  
description of the main source. If needed, go to the Split Screen Menu and  
select Swap Left and Right or Main on Left/Right).  
Main on Left/Right: Selects which side is the main (primary) side. Characteris-  
tics of the main side:  
Source buttons, as well as Aspect Ratio and Auto Image buttons, affect the  
main side only (unsupported source combinations are prevented – see  
above table).  
Turn off Split Screen (go to the Split Screen Menu, then select Main Menu,  
or un-check Split Screen then select Previous).  
Change picture settings.  
Only sound from the main side is audible.  
Turn on Split Screen (go to the Split Screen Menu, then check Split Screen).  
When Split Screen is turned off, the main side is displayed full screen.  
Swap Left and Right: Switches the left and right sources.  
Some RS-232 commands have no effect. See the end of the RS-232 Com-  
mand Additions section later in this document.  
Left/Right Settings: Adjusts aspect ratio, phase, tracking, and horizontal/ver-  
tical position for the left or right side.  
Left/Right Source: Selects the source to display on the left or right side (some  
items will be disabled to prevent unsupported source combinations – see  
above table).  
Split Screen Menu  
Source Info: Shows source information for the left and right sides.  
Main Menu: Turns off Split Screen and goes to the Main Menu.  
To program your remote’s Custom button to display the above Split Screen  
Menu: Go to the Main Menu > Settings > Custom Key menu and select Split  
Screen.  
IMPORTANT - When Split Screen is on, some projector functions work dif-  
ferently:  
The Main Menu and its sub-menus are not available – pressing the Menu  
button shows the Split Screen Menu instead. To turn off Split Screen and  
access other menus from the Split Screen Menu: select Main Menu, or un-  
check Split Screen then select Previous.  
Autosource (source search), Closed Captions and Magnify are not available.  
Download from Www.Somanuals.co3m2. All Manuals Search And Download.  
Auto Power: When Auto Power is checked, the projector automatically  
goes into the startup state after the projector is powered on. This allows  
control of ceiling mounted projectors with a wall power switch.  
Settings menu  
Audio: allows adjustments to the volume. Also allows you to turn on and off  
the Internal speakers and assign a particular source to a specific audio  
input. If your HDMI source has problems with its audio stream, you can  
mute it by selecting HDMI Noise Cancel.  
Display Messages: displays status messages (such as “Searching”) in the  
lower-left corner of the screen.  
Monitor Out Default: Determines the source (either Computer 2 or Computer  
3) which is output through the Monitor Out connector. Computer 2: Out-  
puts Computer 2 unless current source is Computer 3 (in that case output  
Computer 3 instead). Computer 3: Outputs Computer 3 unless current  
source is Computer 2 (in that case output Computer 2 instead). Off: Outputs  
the current source if it is Computer 2 or Computer 3. Otherwise do not out-  
put any signal.  
Settings  
menu  
Audio  
Sources: allows you to assign a particular input to a specific source key  
when using the remote. Also allows selection of a default Startup Source  
and enables or disables Autosource.  
Sources>Power-up Source: this determines which source the projector checks  
first for active signal during power-up.  
Sources>Autosource: When Autosource is not checked, the projector defaults  
to the source selected in Powerup Source. If no source is found, a blank  
screen displays. When Autosource is checked, Powerup Source determines  
which source the projector defaults to at power-up. If no signal is present,  
the projector checks the sources in order until a source is found or until  
power down.  
Powerup  
Source  
Sources  
System>Rear: reverses the image so you can project from behind a trans-  
lucent screen.  
Ceiling: turns the image upside down for ceiling-mounted projection.  
WARNING: To prevent eye injury if the projector is ceiling mounted,  
wear protective eyewear before opening lamp door. A warning sticker is  
included with the user documentation. Place this sticker on the lamp  
door if the projector is mounted on the ceiling.  
IR Receivers: turns individual IR receivers off or on to avoid environmen-  
tal interference.  
IR Receivers  
System  
Download from Www.Somanuals.co3m3. All Manuals Search And Download.  
               
Low Power: toggles between on and off. Turn it on to lower the light out-  
put of the lamp. This also lowers the fan speed, making the projector qui-  
eter.  
on Black: Horizontal lines on a black background. Grid on White: Grid  
on a white background. Grid on Black: Grid on a black background.  
PC Screen Saver Off: prevents your notebook computer from going into  
Screen Save mode. The projector must be connected to the PC via a USB  
cable for this feature to work.  
Screen Save  
Power Save: automatically turns the lamp off after no signals are detected  
for 20 minutes. After 10 additional minutes with no signal, the projector  
powers down. If an active signal is received before the projector powers  
down, the image will be displayed.  
Screen Save: automatically blanks the screen after no signals are detected  
for five minutes. The image returns when an active source is detected or  
a remote or keypad button is pressed. Screen Save is disabled when  
Power Save is enabled.  
Startup Logo: allows you to display a blank Black, White, or Blue screen  
instead of the default screen when no source is detected at startup. It also  
allows you to capture and display a custom startup screen.  
Capture New  
Startup Logo  
To capture a custom logo, display the image you want to capture on  
your computer and select the Capture New option. From the Capture  
New menu, use the Capture Position X and Capture Position Y adjust-  
ments to frame the logo to be captured. Press Capture Start in the Cap-  
ture New menu. The projector will let you know if the capture was a  
success or a failure.  
Blank Screen  
Ruled Lines  
The next time you start the projector, the custom logo you captured dis-  
plays.  
Blank Screen: determines what color is displayed when you press the  
Blank button on an optional remote.  
Ruled Lines: This feature displays line patterns that are useful when pro-  
jecting onto a writeable surface, or when installing and setting up the  
projector. Lines on White: Horizontal lines on a white background. Lines  
Download from Www.Somanuals.co3m4. All Manuals Search And Download.  
               
Custom Key (for use with optional remote only): allows you to assign a dif-  
ferent function to the Custom key on the optional remote to quickly and eas-  
ily use the effect. Only one effect can be enabled at a time. The default is  
Source Info; highlight an effect and press Select to choose a different one.  
IP Address: Identifies the projector on the network.  
Subnet Mask: Separates the network address part of the IP address.  
Default Gateway: The IP address of the local router.  
DNS Server: Shows the address of the DNS server.  
Blank: shows an empty screen.  
Mute: turns off all sound.  
DHCP: Select this to automatically obtain an IP address, Subnet mask,  
and Default gateway.  
AV Mute: turns off all sound and displays a blank screen.  
Aspect Ratio: sets the ratio of the image width to image height.  
Source: cycles through the available sources.  
Auto Image: causes all sources to be reacquired.  
Freeze: pauses the projected image.  
AMX DD: When enabled, allows the AMX controller to dynamically  
detect the projector.  
Network Restart: Disconnects the projector from the network, gets a  
new IP address, and reconnects.  
Network Info: Provides information on the network configuration.  
Magnify: allows you to enlarge a section of the projected image.  
Ruled Lines: displays line patterns that are useful when projecting onto a  
writeable surface, or when installing and setting up the projector.  
Network  
Split Screen: enables or disables Split Screen. Before using this for the  
first time, configure Split Screen sources and layouts using the Split  
Screen menu.  
Source Info: displays the Source Info menu.  
Service Info: displays the Service Info menu.  
Network Info  
Network: The projector has an RJ45 Ethernet connector that supports net-  
work connections and TCP/IP protocols. This will allow for the control and  
management of the projector over a corporate network. Visit our website for  
complete details on using the networking functionality. The following fields  
are accessible when DHCP is not checked and available for manual entry of  
data.  
For network control, you can access the projector through Port 23 (Telnet).  
We use the same control codes on serial as we do over the network. InFocus  
network control uses the Telnet packet structure.  
Download from Www.Somanuals.co3m5. All Manuals Search And Download.  
                     
Language: allows you to select a language for the onscreen display of menus  
and messages.  
Language  
Service: to use these features, highlight them and press Select.  
Factory Reset: restores all settings (except Lamp and Filter Hours and Net-  
work settings) to their default after displaying a confirmation dialog box.  
Reset Lamp Hours: resets the lamp hours counter in the Service Info menu to  
zero. Do this only after changing the lamp. It displays a confirmation dialog  
box.  
Reset Filter Hours: resets the filter counter in the Service Info menu to zero.  
Do this only after cleaning the filter. It displays a confirmation dialog box.  
Service Info: provides information for service.  
Service Code: only used by authorized service personnel.  
Service menu  
Service Info  
Download from Www.Somanuals.co3m6. All Manuals Search And Download.  
           
Maintenance  
clean the lens  
with a soft dry cloth  
and non-abrasive  
cleaner  
Cleaning the lens  
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.  
Avoid using an excessive amount of cleaner, and don’t apply the  
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh  
chemicals might scratch the lens.  
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you  
don’t intend to use the projector immediately, replace the lens cap.  
Download from Www.Somanuals.co3m7. All Manuals Search And Download.  
       
hands after lamp replacement.  
Hg – Lamp contains mercury. Manage in accordance with local  
disposal laws. See www.lamprecycle.org.  
Replacing the projection lamp  
The lamp hour timer in the Service Info menu counts the number of hours  
the lamp has been in use. Twenty hours before the specified end of the  
lamp’s life, the message “Change lamp” briefly appears on the projected  
screen.  
Service Info menu  
NOTE: You can order new lamp housings from www.infocus.com (in select  
areas), your retailer or your dealer. Only genuine InFocus lamps are tested  
for use in this projector. InFocus is not liable for the performance, safety or  
certification of any other lamps. The use of other lamps violates the projec-  
tor warranty and voids all certification marks on this projector.  
1 Turn off the projector and unplug the power cable.  
turn off and unplug  
the projector  
2 Wait 45 minutes to allow the projector to cool thoroughly.  
3 Loosen the lamp cover screw on the right side of the projector (marked  
by the arrow) then slide and lift the lamp cover off.  
wait 45 minutes  
WARNINGS:  
To avoid burns, allow the projector to cool for at least 45 minutes before  
you replace the lamp.  
Only genuine InFocus lamps are tested with this projector. Use of other  
lamps may cause electrical shock and fire.  
To prevent eye injury if the projector is ceiling mounted, wear protec-  
tive eyewear before opening lamp door. A warning sticker is included  
with the user documentation. Place this sticker on the lamp door if the  
projector is mounted on the ceiling.  
Do not drop the lamp module. The glass may shatter and cause injury.  
Do not touch the glass lamp screen. Fingerprints can obscure projection  
sharpness.  
lamp cover screw  
Be extremely careful when removing the lamp housing. In the unlikely  
event that the bulb ruptures, small glass fragments may be generated.  
The lamp housing is designed to contain these fragments, but use cau-  
tion when removing the lamp housing. Before replacing the lamp,  
clean the lamp compartment and dispose oDfocwlnelaonadinfgrommaWtwerwia.Slso.mWanausahls.co3m8. All Manuals Search And Download.  
     
4 Loosen the three captive screws (marked by the arrows) on the lamp  
module. When replacing the lamp, never touch any screws without the  
arrow mark.  
loosen the captive screws on lamp module  
5 Carefully remove the lamp module by grasping and lifting the handle.  
lamp module handle  
Dispose of the lamp in an environmentally proper manner.  
6 Install the new lamp module, making sure that it is properly seated, and  
tighten the three captive screws.  
7 Replace the cover over the lamp module by sliding it back into place and  
tightening the screw.  
8 Plug in the power cable, press the power switch then press the Power  
button to turn the projector back on. Reset the lamp hour timer by navi-  
gating to the Settings>Service menu and selecting Reset Lamp Hours.  
reset lamp hours in Service menu  
Download from Www.Somanuals.co3m9. All Manuals Search And Download.  
 
Cleaning the dust filter  
1 Turn off the projector and unplug the power cable.  
2 Wait 45 minutes to allow the projector to cool thoroughly.  
WARNING: To avoid burns, allow the projector to cool for at least 45  
minutes before you clean or replace the dust filter.  
wait 45 minutes  
3 Remove the dust filter cover on the side of the projector by pressing up  
on the two tabs at the cover’s bottom.  
4 Pull the tab on the center of the black dust filter bracket and lift it off.  
5 Clean the filter, cover, and vent using a vacuum set on low power.  
Replace the filter if it is damaged or too dirty to clean.  
6 Replace the dust filter and the bracket on the cover, then replace the  
dust filter cover.  
7 Reset the filter hour timer by navigating to the Settings>Service menu  
and selecting Reset Filter Hours.  
dust filter cover  
tabs  
reset filter hours in Service menu  
Using the security lock  
The projector has a security lock for use with a cable lock system. See the  
Accessories catalog that came with the projector, or visit our website, for  
ordering information. Refer to the information that came with the lock for  
instructions on how to use it.  
security lock  
Download from Www.Somanuals.co4m0. All Manuals Search And Download.  
       
Appendix  
Projected image size  
NOTE: Visit the Service section of our website for interactive image size cal-  
culators for the standard lense.  
Table 3: Projection sizes: Standard lens (1.5 - 2.9:1 throw ratio)  
Minimum Image  
Maximum Image  
Diagonal  
Image  
Image  
Width  
Diagonal  
Image  
Image Width  
(feet/m)  
Distance (feet/m)  
(feet/m)  
(feet/m)  
(feet/m)  
Min Distance  
3/0.9  
not  
supported  
not  
supported  
2.5/0.8  
2.1/0.7  
5/1.5  
not  
not  
4.1/1.3  
3.5/1.1  
supported  
supported  
6/1.9  
10/3.0  
15/4.6  
20/6.1  
25/7.6  
2.5/0.8  
4.0/1.2  
6.0/1.8  
8.0/2.4  
10.0/3.1  
12.0/3.7  
2.1/0.6  
3.4/1.0  
5.1/1.6  
6.8/2.1  
8.5/2.6  
10.2/3.1  
5.0/1.5  
8.1/2.5  
4.2/1.3  
6.8/2.1  
12.0/3.7  
16.0/4.9  
19.9/6.1  
23.9/7.3  
10.2/3.1  
13.5/4.1  
16.9/5.2  
20.3/6.2  
30/9.1  
37/11.2  
14.7/4.5  
29.2/8.9  
12.4/3.8  
24.7/7.5  
29.2/8.9  
24.7/7.5  
Max Distance  
73/22.3  
not  
supported  
not  
supported  
The image offset range for the standard lens is 10:0 (100%) to 1:1 (50%).  
Download from Www.Somanuals.co4m1. All Manuals Search And Download.  
     
(starts the command  
Command Control  
AAA denotes the command  
Serial Communication Configuration  
Visit our website for additional RS-232 settings and information.  
? denotes the read request  
To control this projector via RS-232, connect a null modem cable and set the  
control system serial port settings to match the following communication  
configuration:  
) ends the command  
A read command returns the range and the current setting, for example:  
RS-232 Port Settings  
Read Command Examples  
Setting  
Value  
19,200  
8
Function  
Command  
(BRT?)  
Response  
Bits per second  
Data bits  
Parity  
Brightness  
Volume  
(96-160,128)  
(0-32,16)  
(VOL?)  
(LMP?)  
None  
1
Lamp Hours  
(0-32766, 42)  
Stop bits  
A write request example:  
(AAA####) where  
Flow control  
Emulation  
None  
VT100  
(starts the command  
AAA denotes the command  
#### denotes the value to be written  
(leading zeros not necessary)  
) ends the command  
Network Communication Configuration  
For network control, you can access the projector through Port 23 (Telnet).  
We use the same control codes on serial as we do over the network. InFocus  
network control uses the Telnet packet structure.  
Command Format  
Some commands have ranges, while others are absolute. If a number  
greater than the maximum range is received, it is automatically set to the  
maximum number for that function. If a command is received that is not  
understood, a "?" is returned. With absolute settings, "0" is off, 1-9999 is on.  
The one exception is the Power command, where 0 is off and 1 is on.  
All commands consist of 3 alpha characters followed by a request, all  
enclosed in parentheses. The request can be a read request (indicated by a  
"?") or a write request (indicated by 1 to 4 ASCII digits).  
A read request example:  
To assure the projector can process a command, wait 3 seconds before enter-  
ing the next command.  
(AAA?) where  
Download from Www.Somanuals.co4m2. All Manuals Search And Download.  
 
Com  
mand  
Write Command Examples  
Function  
RW Min  
Max  
2
Default  
1
Step  
1
Function  
Brightness  
Power  
Command  
(BRT100)  
(PWR0)  
Response  
Active Iris*  
0: Off  
1: Presentation  
2: Film  
IRI  
RW  
0
Sets the brightness to 100  
Turns power off  
Power  
(PWR1)  
Turns power on  
AMX Device Discov-  
ery Enable  
0: Disable; 1: Enable  
AMX  
ARZ  
RW  
RW  
0
0
1
6
0
0
1
1
Error Conditions  
Not all commands are supported for all projectors. If an unsupported com-  
mand is issued, the command will be ignored. If a command is received that  
is not understood, a ‘?’ character will be returned indicating the command  
was not understood.  
Aspect Ratio  
0: Auto  
1: Native  
2: 4:3  
Limitations  
3: 16:9  
6: 16:10  
The projector cannot respond to commands coming in at a high-rate. There-  
fore, a delay must occur between commands to ensure that the command  
gets properly executed.  
Aspect Ratio (Split  
Screen left)  
0: Auto  
ARL  
ARR  
RW  
RW  
0
0
6
6
0
0
1
1
1: Native  
2: 4:3  
3: 16:9  
The Step column refers to increasing or decreasing the menu bar position  
since the On-screen Display is not an exact match of values. For example,  
Step 2 changes the data by 2 through the CLI (Command Line Interface).  
The menu bar is up (or down) by 1.  
6: 16:10  
Aspect Ratio (Split  
Screen right)  
0: Auto  
1: Native  
2: 4:3  
3: 16:9  
6: 16:10  
Download from Www.Somanuals.co4m3. All Manuals Search And Download.  
Auto Image  
1: enable  
AIM  
APO  
ASC  
BLK  
BSC  
W
n/a  
0
1
1
1
1
2
n/a  
0
1
1
1
1
1
Color*  
CLR  
CSM  
RW 96  
160  
4
128  
0
1
1
Color Space*  
0: Auto  
1: RGB  
2: REC709  
3: REC601  
4: RGB Video  
RW  
0
Auto Power*  
0: disable; 1: enable  
RW  
RW  
RW  
RW  
Auto Source*  
0: disable; 1: enable  
0
1
Blank  
0: disable; 1: enable  
0
0
Color Temp*  
0: 9300K  
1: 6500K  
2: 7200K  
3: User  
TMP  
RW  
0
3
1
2 (computer2,  
3)  
0 (computer1,  
video)  
Blank Screen*  
0: black  
1: blue  
0
1
2: white  
Contrast*  
CON RW 96  
160  
1
128  
0
1
1
Brightness*  
BRT  
CEL  
RW 96  
160  
1
128  
0
1
1
Corner Correction  
Enable*  
0: Disable; 1: Enable  
CNE  
RW  
0
Ceiling*  
0: disable; 1: enable  
RW  
0
Corner Correction-  
Top left corner -H*  
CN1  
CN2  
CN3  
CN4  
CN5  
RW  
RW  
RW  
RW  
RW  
0
0
0
0
0
959  
599  
959  
599  
959  
0
0
0
0
0
1
1
1
1
1
Closed Captions*  
0: Off  
1: On  
CCD  
RW  
0
2
0
1
Corner Correction-  
Top left corner -V*  
2: Auto  
Closed Captions  
Channel*  
0: CC1  
1: CC2  
2: CC3  
CCC  
RW  
0
7
0
1
Corner Correction-  
Top right corner -H*  
Corner Correction-  
Top right corner -V*  
3: CC4  
Corner Correction-  
Bottom left corner -  
H*  
4: Text1  
5: Text2  
6: Text3  
7: Text4  
Download from Www.Somanuals.co4m4. All Manuals Search And Download.  
Corner Correction-  
Bottom left corner -  
V*  
CN6  
CN7  
CN8  
CNR  
RW  
RW  
RW  
RW  
0
0
0
0
599  
959  
599  
1
0
1
1
1
1
Custom Key (Effect)*  
0: Blank  
1: Mute  
2: Aspect ratio  
3: Source  
4: Auto image  
5: Freeze  
EFK  
RW  
0
18  
7
1
Corner Correction-  
Bottom right corner -  
H*  
0
6: Magnify  
Corner Correction-  
Bottom right corner -  
V*  
0
7: Source Info  
8: Service Info  
15: AV Mute  
17: Split Screen  
18: Ruled Lines  
n/a  
Corner Correction all  
corners Reset*  
0: n/a  
1: enable  
Display Messages*  
0: disable; 1: enable  
DMG RW  
0
1
1
1
1
1
Source  
SRC  
RW  
0
5
0
1
Factory Reset*  
1: reset  
RST  
W
n/a  
n/a  
0: computer1  
1: computer2  
2: computer 3  
3: video 1  
4: video 2  
5: video 3  
Filter Hours  
RFT  
FRZ  
R
0
0
32766  
1
0
0
Freeze  
0: disable; 1: enable  
RW  
1
1
HDMI Noise Cancel*  
0: Not Reset  
1: Reset  
HNC RW  
0
1
1
Horizontal Keystone*  
Horizontal Position  
DKH  
HPS  
RW 88  
168  
128  
1
1
RW Def.  
-128  
Def.  
+128  
auto  
Horizontal Position  
(Split Screen left)  
HPL  
RW Def.  
-128  
Def.  
+128  
auto  
1
Download from Www.Somanuals.co4m5. All Manuals Search And Download.  
Horizontal Position  
(Split Screen right)  
HPR  
INT  
RW Def.  
-128  
Def.  
+128  
auto  
1
1
1
Language*  
0 = English  
1 = French  
2 = German  
3 = Italian  
LAN  
RW  
0
17  
0
1
Internal Sound  
Enable*  
0: disable; 1: enable  
RW  
0
1
5 = Korean  
6 = Norwegian  
7 = Portuguese  
8 = Russian  
9 = Simp. Chinese  
10 = Spanish  
11 = Trad. Chinese  
12 = Swedish  
13 = Dutch  
IP Address Byte 1  
IP Address Byte 2  
IP Address Byte 3  
IP Address Byte 4  
IP1  
IP2  
IP3  
IP4  
IRF  
R
0
0
0
0
0
1
1
1
1
1
192  
168  
1
R
R
R
254  
1
IR Receiver front*  
0: disable; 1: enable  
RW  
1
1
1
14 = Polish  
15 = Turkish  
16 = Danish  
17 = Finnish  
IR Receiver rear*  
0: disable; 1: enable  
IRR  
IRT  
RW  
RW  
0
0
1
1
1
0
Lamp Hours Used: All  
Bulbs  
LMT  
R
0
21474  
83646  
0
IR Receiver top*  
0: disable; 1: enable  
Lamp Hours  
LMP  
LB1  
LB2  
LB3  
LML  
R
R
R
R
R
0
0
0
0
0
32766  
32766  
32766  
32766  
1
0
Lamp 1 Lasted (Hrs)  
Lamp 2 Lasted (Hrs)  
Lamp 3 Lasted (Hrs)  
0
0
0
Lamp Lit  
n/a  
0: not lit; 1: lit  
Lamp Resets (Total)  
LMR  
LPE  
R
0
0
32766  
1
0
0
Low Power*  
RW  
1
0: disable; 1: enable  
Download from Www.Somanuals.co4m6. All Manuals Search And Download.  
Magnify*  
MAG RW  
0
0
48  
1
0
0
1
1
Phase (Split Screen  
left)  
MSL  
RW  
RW  
RW  
0
0
0
31  
31  
1
0
0
0
1
1
1
Magnify Enable*  
0: disable; 1: enable  
MGE  
RW  
RW  
RW  
Phase (Split Screen  
right)  
MSR  
PWR  
Magnify Position Hori- MPH  
zontal*  
0
0
0
0
64  
64  
1
32  
32  
0
1
1
1
1
Power  
0: Turn Off; 1: Turn  
On  
Magnify Position Ver-  
tical*  
MPV  
Power Save*  
0: disable; 1: enable  
PSV  
RW  
RW  
0
0
1
5
0
0
1
1
Menu  
0: clear; 1: display  
MNU RW  
Power-up Source*  
0: computer 1  
1: computer 2  
2: computer 3  
3: video 1  
DSC  
Menu Navigation  
0: up key  
1: down key  
4: select key  
NAV  
W
4
n/a  
4: video 2  
5: video 3  
Monitor Out Default* MO  
RW  
1
5
1
1
1: Computer 2  
2: Computer 3  
5: Off  
D
Presets*  
0: user 1  
PST  
RW  
0
11  
1
5 (computer  
2, 3)  
1: user 2  
2: user 3  
3: Presets Off  
5: presentation  
7: video  
7 (computer1,  
video)  
Mute  
0: disable; 1: enable  
MTE  
NTR  
OVS  
RW  
W
0
1
0
1
1
1
1
1
Network Restart*  
1: restart  
n/a  
0
1
n/a  
0
10: bright  
11: whiteboard  
Overscan*  
0: disable; 1: enable  
RW  
1
Rear*  
0: disable; 1: enable  
REA  
FRT  
RW  
W
0
1
1
0
1
1
PC Screen Saver Off*  
0: disable; 1: enable  
NND RW  
0
1
1
Reset Filter Hours  
1: reset  
n/a  
n/a  
Phase  
MSS  
RW  
0
31  
0
Download from Www.Somanuals.co4m7. All Manuals Search And Download.  
Reset Lamp Hours  
1: reset  
LRT  
RLL  
W
n/a  
0
1
3
n/a  
0
1
1
Source 0 Audio*  
0: audio 1  
1: audio 2  
2: audio 3  
3: audio 4  
SA0  
SAn  
RW  
RW  
0
0
5
5
4
1
1
Ruled Lines*  
RW  
0: Lines on White  
1: Lines on Black  
2: Grid on White  
3: Grid on Black  
4: HDMI Internal  
5: mute  
Source 1-5 Audio*  
0: audio 1  
1: audio 2  
2: audio 3  
3: audio 4  
Source 1=  
0
Source 2=  
1
Source 3 =  
3
Source 4 =  
Ruled Lines Enable  
0: disable; 1: enable  
RLE  
USn  
RW  
W
0
1
1
0
1
1
Save User Presets 1-  
3*  
1: save  
n/a  
n/a  
5: mute  
2
Screen Save*  
0: 5 minutes  
1: 10 minutes  
2: 15 minutes  
3: 20 minutes  
4: 25 minutes  
5: 30 minutes  
SSV  
RW  
0
5
5
0
1
Source 5 =  
2
Source 1*  
SR1  
SR2  
RW  
RW  
0
0
5
5
0
1
1
1
0: computer 1  
1: computer 2  
2: computer 3  
3: video 1  
4: video 2  
5: video 3  
Sharpness*  
5 = Sharpest  
6 = Sharper  
7 = Standard  
8 = Softer  
SHP  
RW  
9
1
7 (computer  
and video 1)  
6 (video 2  
and 3)  
Source 2*  
0: computer 1  
1: computer 2  
2: computer 3  
3: video 1  
9 = Softest  
4: video 2  
5: video 3  
Download from Www.Somanuals.co4m8. All Manuals Search And Download.  
Source 3*  
SR3  
SR4  
RW  
RW  
0
0
5
5
3
4
1
1
Split Screen Right  
Source  
0: Computer 1  
1: Computer 2  
2: Computer 3  
3: Video 1  
SSR  
RW  
0
5
2
1
0: computer 1  
1: computer 2  
2: computer 3  
3: video 1  
4: video 2  
5: video 3  
4: Video 2  
5: Video 3  
Source 4*  
0: computer 1  
1: computer 2  
2: computer 3  
3: video 1  
4: video 2  
5: video 3  
Split Screen Swap Left  
and Right  
1: Execute Swap  
SSS  
W
n/a  
0
1
2
n/a  
1
1
1
Startup Logo*  
0: blank screen  
1: default  
DSU  
RW  
Source Info  
1: enable  
ABT  
SSC  
SSM  
SSL  
W
n/a  
0
1
1
1
5
n/a  
0
1
1
1
1
2: captured  
Sync on Green*  
0: Disable; 1: Enable  
SOG  
RW  
0
1
1
1
Split Screen  
0: Disable; 1: Enable  
RW  
RW  
RW  
Tint*  
TNT  
MTS  
RW 96  
160  
128  
1
1
Split Screen Main Side  
0: Left; 1: Right  
0
0
Tracking  
RW def.  
-384  
def.  
+384  
auto  
Split Screen Left  
Source  
0: Computer 1  
1: Computer 2  
2: Computer 3  
3: Video 1  
0
1
Tracking (Split Screen  
left)  
MTL  
MTR  
ONL  
DKC  
RW def.  
-384  
def.  
+384  
auto  
auto  
0
1
1
Tracking (Split Screen  
right)  
RW def.  
-384  
def.  
+384  
4: Video 2  
5: Video 3  
Unit Total Time On  
R
0
21474  
83646  
Vertical Keystone*  
RW 48  
208  
128  
1
Download from Www.Somanuals.co4m9. All Manuals Search And Download.  
Vertical Position  
VPS  
VPL  
VPR  
RW if  
def<1  
def+  
128  
auto  
auto  
auto  
0
1
1
1
1
28 : 0  
else:  
def-  
128  
Vertical Position (Split  
Screen left)  
RW if  
def+  
128  
def<1  
28 : 0  
else:  
def-  
128  
Vertical Position (Split  
Screen right)  
RW if  
def+  
128  
def<1  
28 : 0  
else:  
def-  
128  
Video Standard*  
0: Auto  
1: NTSC  
2: PAL  
3: SECAM  
VSU  
VOL  
RW  
RW  
0
3
Volume  
0
32  
16  
1
1
Red Gain*  
Green Gain*  
Blue Gain*  
RCG  
GCG  
BCG  
RW 64  
192  
128  
* These RS-232 commands have no effect when Split Screen is on.  
Download from Www.Somanuals.co5m0. All Manuals Search And Download.  

Indesit Washer GB Washing Machine User Manual
Insignia Child Tracker NS KDTR1 User Manual
Insignia CRT Television NS RTV32 User Manual
Insignia MP3 Player NS DVB2G DVB4G User Manual
Jenn Air Charcoal Grill JGD8348CD User Manual
Kenwood Car Amplifier KAC M846 User Manual
Kenwood DVD Recorder KMD 673R User Manual
Kinyo Speaker HT 1037 User Manual
KitchenAid Blender KSB560BW0 User Manual
Knoll Stereo System MR164 User Manual